37!
No broken bits this time not even any skin, extremely bruised back though, bit tough to breath, sitting on couch with a board behind my back to ease the pain.
ejit made an illegal u-turn across my lane, alwell least i took a big chunk of it.
bit cold the other day! clocks need setting straight they were always a bit bent looks a lot worse now with the screen to align them with.
125cc racer, note foldable pegs, large 90 tank, sticky rear tyre, can’t race this because its breaks the rules, but we might as well finish it now. Will bring it to watergrasshill to test it along side with my rxs100 probably next month since the race is feburary
It looks like a katana!
well i hope it does, some ejit will say it looks like a bmw
noticed my tak welds were good enough to support me hanging off the subframe, so i welded it a bit more and left it at that.
Sprayed it black
That too, cleanest it’s even been.
quick and dirty
was thinking reverse paint scheme, but that’s not gonna work, magnolia with black stripe all the way
bonus! clocks fit, might use em.
best looking angle, and the most important.
cbr6 get a new nose
Garage was a bit blocked up so i did some work outside.
Not too bad, can’t decide weather to shorten the nose or lower it, want it to have a hint of 80’s suzuki katana, might chop off the nose of old front mudguard.
tak welded together
Bit of adjustment todo, gonna be painted magnolia again, with a black stripe down the middle (or maybe another colour…..)
handguards on a sports bike.
Delivery’s came, so first thing was puting the new belt on the runner, just so I could get it out of the garage. Also came the parts for the english axle, right after I decided to not bother with it.
Ran the oily rag around it coz it’s sold, pity I insured it only got a few months out of it. Gotta plough on with the ypvs/xt hybrid need a two-stroke toy!
Sarges vn1500a (or vulcan 88) in all it’s glory.
Yep it looks worse up close. Found the approximate setting for the carbs (one post out there on the net!) no more then 138 main jet and the needle high on the 4th clip
Wanted to get these on for the winter.
There a bit small for wind protection and no use as crash protection
Also the taper insert thing was too small at 13mm, need one to fit an 18mm id, handle bars are confusing 7/8″ is 22mm so when they say to fit a 22mm bar do they mean 22mm od or id? a 22mm id would be massive.
Need a solid conection at the bar to hold the wind shield, rubber won’t do at 120mph.
Birdies haven a bath on the garage.
Also got the rear leaves of the jago half painted.
stuff done today.
Got that bultaco that was in the garage for a while started, do these people not know that is there is too much oil in the premix the fuel leans out and that’s nearly as bad as not have enough oil? he only wants €600 for it, was tempted till I realised it’s righthand gearchange.
New pads for the runnner 180, gotta sell it off now.
New oil and filter for the poor suffering cbr6, really needs a rear tyre now.39500miles on the clock now, which makes its about 75000miles?
50mm spring on the left and a 60mm spring on the right. whew that’s cleared up a lot of my worries about this back end being a mk1,I now know for certain its a mk2, sweet.
turned it around by lifted it up with one hand and spinning it around like a top. over my head. whilst keeping the crocodiles back with a whip and a chair. with my third arm.
you can see it clearer now that the shite on the floor is gone.
Another new bit needed, think this was part of the reason why the spring broke.
Tub off and Paint on.
Fromt this angle its good.
Not so from this angle, too plain.
Needs that front end from the dr750, or the rear shortened.
Tub off!
Must get all the wood out and plan ahead for the new floor.
50mm rear leafs and a big bar that pulls both drum for the hand brake points to a mk1 rear end? i could be quite wrong tho.
What gearbox do we have? 4 speed anyway.
OL25A2?
I think that was meant to be a freeze plug..
Whole thing is quite solid, but then again it would take a lot of punishment to actually rust steel this thick.
Hope the starter motor is okay on that side, crossflow is a bit different then the pinto.
